# Configuration file for svgalib. Default location is /etc/vga.
# Lines starting with '#' are ignored.

# Have a deep look at README.config to see what can do here (especially
# for mach32).

# Mouse type:

# mouse Microsoft	# Microsoft
# mouse MouseSystems	# Mouse Systems
# mouse MMSeries	# Logitech MM Series
# mouse Logitech	# Logitech protocol (old, newer mice use Microsoft protocol)
# mouse Busmouse	# Bus mouse
# mouse PS2		# PS/2 mouse
# mouse MouseMan	# Logitech MouseMan
# mouse none		# None

mouse microsoft

# Some multiprotocol mice will need one of the following:

# setRTS   # set the RTS wire.
# clearRTS # clear the RTS wire.
# leaveRTS # leave the RTS wire alone (default) (Wire is usually set)
# setDTR   # set the DTR wire.
# clearDTR # clear the DTR wire.
# leaveDTR # leave the DTR wire alone (default) (Wire is usually set)

# Monitor type:

# Only one range can be specified for the moment.  Format:
# HorizSync min_kHz max_kHz
# VertRefresh min_Hz max_Hz

# Typical Horizontal sync ranges
# (Consult your monitor manual for Vertical sync ranges)
#
# 31.5 - 31.5 kHz (Standard VGA monitor, 640x480 @ 60 Hz)
# 31.5 - 35.1 kHz (Old SVGA monitor, 800x600 @ 56 Hz)
# 31.5 - 35.5 kHz (Low-end SVGA, 8514, 1024x768 @ 43 Hz interlaced)
# 31.5 - 37.9 kHz (SVGA monitor, 800x600 @ 60 Hz, 640x480 @ 72 Hz)
# 31.5 - 48.3 kHz (SVGA non-interlaced, 800x600 @ 72 Hz, 1024x768 @ 60 Hz)
# 31.5 - 56.0 kHz (high frequency, 1024x768 @ 70 Hz)
# 31.5 - ???? kHz (1024x768 @ 72 Hz)
# 31.5 - 64.3 kHz (1280x1024 @ 60 Hz)

HorizSync 31.5 35.5
VertRefresh 50 70

# Montitor timings
#
# These are prefered over the default timings (if monitor and chipset
# can handle them). Not all drivers use them at the moment, and Mach32
# has its own syntax (see below).
# The format is identical to the one used by XFree86, but the label
# following the modeline keyword is ignored by vgalib.
#
# Here some examples:

# modeline "640x480@100"  43  640  664  824  848   480  483  490  504
# modeline "800x600@73"   50  800  856  976 1024   600  637  643  666
# modeline "1024x768@75"  85 1024 1048 1376 1400   768  771  780  806

# Mach32 timings:

# e.g. Setup a 320x200 mode for the mach32:

define 320x200x32K 320x200x64K 320x200x16M 320x200x16M32
                     16 320 392 464 552 200 245 265 310

# These are REQUIRED for above mode, please edit to suit your monitor.
# (No, I won't pay for a new one)
# HorizSync 29 65
# VertRefresh 42 93.5

# Chipset type:
#
# Use one of the following force chipset type.
# Autodetects if no chipset is specified.
# If a chipset driver gives trouble, try forcing VGA.

# chipset VGA		# Standard VGA
# chipset EGA		# EGA
# chipset ET3000	# Tseng ET3000
# chipset ET4000	# Tseng ET4000
# chipset Cirrus	# Cirrus Logic GD542x
# chipset TVGA		# Trident TVGA8900/9000
# chipset Oak		# Oak Technologies 037/067/077
# chipset S3		# S3 chipsets
# chipset GVGA6400	# Genoa 6400
# chipset ARK		# ARK Logic
# chipset ATI		# old ATI VGA
# chipset Mach32	# ATI Mach32
# chipset ALI		# ALI2301
# chipset Mach64	# ATI Mach64

# EGA Color/mono mode:
# Required if chipset is EGA.
#
# Use one of the following digits to force color/mono:

# monotext  # Card is in monochrome emulation mode
# colortext # Card is in color emulation mode
colortext

# RAMDAC support:
# Some chipsets (e.g. S3 and ARK) allows specifying a RAMDAC type.
# If your RAMDAC is not autodetected, you can try specifying it.
# Do NOT specify a RAMDAC if you card uses the S3 Trio chipset
# (the RAMDAC is built in).

# Ramdac Sierra32K
# Ramdac SC15025
# Ramdac SDAC         # S3 SDAC
# Ramdac GenDAC       # S3 GenDAC
# Ramdac ATT20C490    # AT&T 20C490, 491, 492 (and compatibles)
# Ramdac ATT20C498    # AT&T 20C498
# Ramdac IBMRGB52x    # IBM RGB524, 526, 528 (and compatibles)

# Dotclocks:
# Some chipsets needs a list of dot clocks for optimum operation.  Some
# includes or supports a programmable clock chip.  You'll need to specify
# them here.

# Fixed clocks example:
# (The following is just an example, get the values for your card from
#  you XF86Config)

# Clocks 25.175 28.3 40 70 50 75 36 44.9 0 118 77 31.5 110 65 72 93.5

# Programmable clockchip example:

# Clockchip ICD2061A  # The only one supported right now